2.4GHz Wireless Color Camera
System This wireless camera system has a four channel sequencing
receiver. You can add extra cameras (up to 4) to this wireless camera
and receiver set. The sequencing speed is set by you each camera will
show for a pre determined amount of time and then switch to the next
camera automatically. This wireless camera set does not allow for
all cameras to be viewed at once.
Features:
Transmits video and
audio signals from one AV device to another wirelessly
Built-in rechargeable
Lithium battery in camera, for at least 5 hours continuous working
4 channel available to
avoid interference
Built-in microphone in
camera w/IR LEDs for night vision
400’ transmission
distance in line of sight
Specifications:
Receiver:
Demodulation FM (Video/Audio)
RF frequency 2,400 to 2,483MHz
Current consumption 700 mA
Power supply DC 5V, 200 mA
Operating Temperature 14ºF to 122ºF
Operating humidity 85%RH
Dimensions 80(W) x 130(L) x 38(H) mm
Weight 250g
Camera:
Image sensor 1/3” C-MOS
Number of pixels NTSC: 510x492, PAL: 628x582
Horizontal resolution 380 TV Lines
Min illumination 1.5Lux @F1.5
RF frequency 2,400 to 2,483MHz
Channel frequency CH1: 2,414MHz CH2: 2,432MHz
CH3: 2,450MHz CH4: 2,468MHz
Modulation FM (Video/Audio)
Battery Lithium, 500mAH
Current Consumption 80 mA
Operating Temperature 14ºF to 122ºF
Operating humidity 85%RH
Dimensions 23(W) x 66(L) x 23(H) mm
Weight 60g
Power supply DC 5V, 700 mA
WIRELESS CAMERA---CW3510TX
INSTALLATION 1. Connect the supplied adaptor (DC 5V
700mA) to the DC IN jack on the rear
of the camera and plug it into AC
power outlet. The red LED (power
indicator light) on the back of the
camera will be lit and the battery
(inside the camera) will be charging
(green LED). 2. Charge the battery first for 2 hours
prior to use. 3. Select the channel you wish to view.
WIRELESS
RECEIVER---CW3510RX 1. Connect the supplied AC adaptor (DC 8V 200mA) to
the DC IN jack of the receiver and plug it into AC
outlet. 2. Connect the supplied A/V cable to the jack. Plug the
yellow colored RCA to the VIDEO IN on the
monitor/TV and the white colored RCA to the AUDIO
IN respectively. 3. Turn on the power switch. 4. Press the channel selection button to select the same
channel as the camera.
OPERATION WITH TV/MONITOR
AND VCR
1.Connect the provided A/V (audio/video) cable to the A/V jack on the
receiver and to the jacks
on your VCR’s A/V jacks.
Be sure to connect the white connector of the A/V cable to the AUDIO IN
jack and the yellow
connector of the A/V cable to the VIDEO IN jack on the VCR, if the VCR
has only a single jack for
video input, connect the yellow plug to it.
2.Connect the other A/V cable (not supplied) to the VIDEO OUT and AUDIO
OUT jacks on
your VCR. Connect the other ends to VIDEO IN and AUDIO IN jacks on your
TV/monitor.
3. Plug the provided AC adapter (DC 8V 200mA) into the DC jack on the
receiver and the other
end into AC outlet.
Make sure the POWER switch is in the OFF position beforehand.
4.Locate and orient the receiver to get optimal performance.
5.Be sure the TV/monitor and the receiver are turned on.
*Free
Ground Shipping is available in the United States only
It is the responsibility of the Buyer (not
Spyville.com its subsidiaries, officers or
partners) to ascertain and obey all applicable
local, state, international and federal laws in
regard to possession and use of any of our
products. Consult your attorney regarding local,
state, international and federal laws before
ordering. By placing an order, the buyer
represents that he/she is of legal age and that
the products will be used only in a lawful
manner. Spyville.com its subsidiaries, officers
or partners will not be responsible for the
misuse, illegal use or inability to use our
products .
